How to Clean Hardwood Floors without a Mop?

Cleaning is fun and all until your mop breaks off! How can you clean the floor without a mop?  And when it is hardwood floor, you might find it tough to deal with the build-ups. Don’t worry about how to clean hardwood floors without a mop; we have easy tricks for you!

Steps to Clean Hardwood Floors without a Mop 

Take a look at the easy tips and tricks to keep the hardwood floor clean even without the mop! 

1. Gather the Tools 

First of all, get your hands on the right brush for cleaning. You can settle for a piece of cloth too. In short, a brush, cloth, or sponge will do the job. For scrubbing off any tough stains or dirt, a brush can be helpful. 

Keep a brush handy even if you use a cloth or sponge. In the case of the cloth, pick up a microfiber cloth. As you are not using a mop, the right cleaner is the utmost priority here. 

Choosing the right cleaner for the floor type you have, you can get help from TidyFloor. This site will not only tell you about the ideal cleaner but will also deal with how to use it for the best outcome! 

2. Prepare the Solution 

You are done with choosing the tools for cleaning now get a hold of a bucket and fill it up with water. Add the cleaner in the water according to how much area you are going to clean. Mix the solution with the water properly. 

3. Remove the Loose Dirt 

With the help of a brush, clean the loose dirt from the floor now. The loose debris will make it messy if you don’t take them off. After brushing off the loose dirt, take it away with the help of a broom. 

4. Get the Equipment Ready 

When the area has no loose dirt anymore, get the cloth into the water. You can use a brush or sponge in this step as we have mentioned above. Soak the brush, sponge, or cloth into the water and wring it out so that no additional water is there. Otherwise, the floor will get wet.  

5. Start Cleaning 

It’s time to kneel on the floor. Make sure you are kneeling in a way that the dirt or the dirty sponges you are using here do not touch your clothes. 

After kneeling on the floor, you have to start scrubbing the floor. Make sure you are scrubbing in sections. Do not start sweeping the entire floor as it will not help you deep clean the area. 

6. The Final Touch  

Now, you are done with scrubbing the floor in sections. Once you are done cleaning every section, don’t forget to give it a final sweep. 

Get the sponge, cloth, or brush into the water once again and wring it. Then, give it a final sweep the take off the leftover dirt and debris. 

7. Dry the Floor 

And you are done cleaning the floor! Don’t walk on the floor when it is wet as it will attract more dirt. Instead, give the floor enough time to dry. You can settle for wiping up or vacuuming the loosened debris afterward if you want. Now the floor is completely cleaned! 

See, it isn’t tougher than cleaning with a mop, right? If you hate to work with a sponge or cloth, settle for vacuum cleaners. Your job will be a lot easier will a vacuum backing you up! Until then, a sponge can solve all your problems! 

Kitchen Sinks

If you have recently built a house or just remodeled your existing kitchen, there is a good chance that you will need a good kitchen sink.

There are so many things that you need to consider when purchasing your kitchen sink as well as installing it and maintaining it.

It is very important that you have chosen the kitchen sink that will best fit your needs. It is important to understand that sinks that aren’t hooked up properly can cause serious damage to the rest of the kitchen.

The Henderson’s decided to remodel their kitchen. It had been several years since they bought their home and the kitchen looked very outdated. The existing sink in their kitchen was very old. It had been painted and the white paint was peeling and revealing black paint underneath. The Henderson’s set out to get their new sink.

Choosing the sink that is right for you

When you are looking for the kitchen sink that is right for you, you need to take several things into consideration. There is not just one standard sink. There are many different styles, materials, and accessories that you can choose.

The first thing that you need to choose is the material of the sinks. In the past few years, stainless steel has become very popular. You can purchase a stainless steel stove, stainless steel fridges, and even stainless steel accessories such as toasters and blenders.

Now, if you want your sink to match the rest of your decor, you can purchase a stainless steel sink. If you are looking for a fancier more classical look, marble sinks are the way to go. If you are looking for something simple and traditional, you should take a look at granite sinks. The marble and granite sinks usually come in a variety of colors or you can purchase one in white.

The next thing that you need to decide is the style of the sink. First, you should decide if you want a double sink or a single. A double sink comes in handy for washing dishes. You can wash on one side and rinse on the other.

Another use for the double sink is to put the strainer in for your dishes to dry in. If you lack counter space, putting the strainer in one side of the double sink can be easier. Most double sinks are square and when split, each side becomes a rectangle. If you choose a single sink however, you can choose between an oval sink and a square sink.

You can purchase a faucet that has a purification system in it. This purifies your water so that it is cleaner and better tasting. Other than the water purification faucets, they are, for the most part, the same.

How to change a table saw blade?

If you are a woodworker and often use, a table saw. It’s a particular question for you how to change a table saw blade details?

The answer I will show step by step process. But you should know when it’s time to change the blade. Right!

How to know when your blade is dull?

It’s a common problem for a woodworker. If you have a maintaining routine for this, you don’t need to worry at all.

But if you are a newbie or don’t know after how many hard projects you should change those blades.

Make sure you read the full article to gain this knowledge.

It’s high time to change your table saw blade when you see these symptoms.

1. Bent blade, Alignment problems, these are the common problem.
2. But if your blade makes a burn on wood, this is serious, and you need to take the step to change it.

I suggest not to buy a new one.

You can clean it by using super washer liquid. Take a half bucket of cleaner and leave those blades for 20min.

And boom. Your blades are ready to go like a new one.

As I mentioned if your blades are facing situation 1. You have to a new table saw blades. Need a review for this? Visit this link.

Sometimes it’s a wise decision to sharp the blade instead to buy a new one. But if your blade’s teeth are broken.

Especially for 80 teeth blade. Don’t be so smart that you can manage with broken teeth, however.

It will hamper your project that can’t be undone. Take my decision to change it with a new one.

Changing table saw blade is an essential task for carpenters. So, do it yourself in just 10 min.

What tools do you need to do it?

1. Screwdriver.
2. Wrench.
3. Of course, the new blade.
4.  Small block of wood for support.

Caution:

1. Turn off the power.
2. Wear safety gloves.

Step by step process:

To remove the blade 1st lose the screws. Some edges are a tie with more than one screw.

Make sure you lose all the screws.

1. When you lose the screw, the blade loses tension and start to move. So, use a plank of wood to block it.
2. Remove the nut and washer with the help of a wrench.
3. Take the new blade and repeat all this thing. Use a wrench to tighten the screws.
4. Then install the guard system and throat plate.
5. You are now ready to go.
6. Turn on the power and make sure the blade is moving correctly.

Conclusion:

 Now you know the procedure correctly. This is a straightforward process, but which part should you consider fast.

It will never bother you next time to change the table saw blade. It’s so similar with changing miter saw blade also.

All I have mentioned in the article. Thank you. Good luck with your next woodworking projects.

Types of Sinks

There are a few different types of sinks. Each type of sink has a different style and a different purpose.

The first type of sink is the kitchen sink. The kitchen sink is exactly what its name says. It is a sink in the kitchen.

A kitchen sink is a necessary part to one’s kitchen. The kitchen sink’s major purpose is to wash dishes. For years, people have been washing dishes in the sink. Since the invention of the dishwasher, however, the kitchen sink has had a bit of a break from washing the dishes. The kitchen sink is still used for many things. Washing hands, cooking, and soaking items name a few. Kitchen sinks have a few different styles.

The older sinks are just one large basin. This makes washing and rinsing the dishes a bit more difficult. The newer sinks have two basins. This sink isn’t larger, it is just slit in half. This way, one side can be used for washing and the other side for rinsing.

Having a double-sided sink just makes things easier. Most people these days do not like to drink the water from the faucet in their kitchen sink. With all of the chemicals used to clean the water as well as possible pollution, most people use bottled water for drinking purposes. Some people choose to have a water filtration system.

It may seem like a large expensive piece of equipment but it is not. All a water filtration system is, is a small tube-shaped object which is hooked over the faucet. This purifies the water as it comes out of the faucet. There is also a water purifying pitcher. This is a pitcher that has unpurified water poured into it and the water is purified when it comes out. The purification system is in the spout of the pitcher. The invention of the kitchen sink has made cooking in the kitchen much easier.

The older sinks are just one large basin.  This makes washing and rinsing the dishes a bit more difficult.  The newer sinks have two basins.  This sink isn’t larger, it is just slit in half. This way, one side can be used for washing and the other side for rinsing.

Another type of sink is the bathroom sink. The bathroom sink is just what its title says. A sink in the bathroom. The bathroom sink, unlike the kitchen sink, is not made for washing dishes. The bathroom sink is made more for personal grooming than household chores.

What Should I Consider when Choosing a Sink Material?

There are a few things to take into consideration when choosing a material for your sink. The first thing is always, will the material of your choice look silly.

It is not wise to choose a material that does not go right. Stainless steel, for example, looks nice in bar sinks or kitchen sinks. You will not find stainless steel sinks in the bathroom.



Another fact to take into consideration is the durability. It is well known that brass sinks are damaged very easily. It would not be wise to make a utility sink out of brass. It would be broken in a second.

When purchasing a new sink, it is a good idea to consider every aspect before deciding on anything. Thinking it all through first will save a lot of time and effort. If you choose the wrong sink, you will need to start over.

The bathroom sink

The bathroom sink is where people brush their teeth, where they wash their hands, and also where men shave. There are several grooming activities done in a bathroom sink. The bathroom sink in generally smaller than the kitchen sink. It is usually set in a vanity. There is a much larger selection of bathroom sinks than kitchen sinks. Bathroom sinks come in many more shapes and sizes. There are round sinks, square sinks, rectangle sinks, oval sinks, and even seashell shaped sinks. There are many different colors as well.


Another sink type is a bar sink. The bar sink is self descriptive. It is a sink in a bar. A bar with a sink is called a “wet bar.” Most bar sinks, especially bar sinks for the home, are made to look nice. A very nice material used for bar sinks is brass. A brass sink is a delicate sink. It can be scratched easily, but it is the nicest material for an elegant bar sink. Any sink material can be used. There are many other nice materials as well.


Another type of sink is a utility sink. A utility sink is used in basements, laundry rooms or garages. Utility sinks are used to clean large, heavy duty items. Washing work boots, lawn ornaments, and sweaters that are hand wash only.

Sink Materials

There are many different materials used when making sinks. For long last and durability, stainless steel is a good choice. You can get a kitchen sink, bar sink, or utility sink in stainless steel. Another durable material for a sink is granite.

The granite does not scratch easily. The more delicate materials such as brass and glass are usually used in bar sinks or any other type of sink where scratching the sink is unlikely. Copper sinks are an excellent choice. They have a beautiful quality and they improve with age.

The older a copper sink gets, the more beautiful the sink becomes. The color turns to a rich, deep, beautiful color. Another wonderful quality is that copper sinks can repair themselves if they are scratched. This makes copper sinks a wonderful choice.


The sink may be one of the best inventions ever. The sink has made our lives so much easier for well over a century. Before sinks, people were forced to bring their water in from outside and pour it into a basin. After several years, the sink has come a long way.

These days, you can find sinks made out of several different types of materials.


It is no longer necessary for anyone to run outside and get their own water. Lucky for us, someone invented indoor plumbing. For years, we have been able to turn water on right inside our homes and the water comes right in.